Autel IM608 BMW FEM All Keys Lost Car Not Start Solution
Here comes a similar problem: Autel IM608 PRO programs BMW 420d 2014 all keys lost, everything went nice and smooth extracting all info from FEM […]
Here comes a similar problem: Autel IM608 PRO programs BMW 420d 2014 all keys lost, everything went nice and smooth extracting all info from FEM […]
Problem: 2018 BMW 430i FEM/BDC pulled FEM and DME, took home to do on bench. Went to input DME number so I can read ISN […]
Yanhua Mini ACDP module 11 supports both BMW E series and F series 8HP EGS ISN clear function. Here is the guide to clear F chassis […]
Easy guide to read ISN code from MINI Cooper MEV17.2.2 Engine ECU using CGDI Prog BMW key programmer. Run CGDI BMW software, Select BMW ISN […]
CG Pro 9s12 allows changing BMW CAS1-CAS4 VIN via eeprom easily. Here is an example of CAS2. Select VIN function Open and upload eeprom […]
CGDI Prog BMW, Yanhua Mini ACDP and VVDI BIMTool pro which one do you recommend for BMW Locksmith & Engineer? Here is the clue. […]
Question: I need a Yanhua Mini ACDP pinout for BMW CAS 2 module without interface board. I don’t have the interface board, where can i get […]
Autel MaxiIM IM508, IM608 and IM608 Pro released new BMW Mini Immo software version on Jan. 14th, 2023. IMMO BMW 1. Optimize process for key learning via […]
Problem: I need to program EWS3 key with Autel IM508 and XP400 Pro. There is no way to do ews3. I have done everything but […]
Question: What is the procedure to read BMW F30 FEM DME ISN using Yanhua Mini ACDP? Solution: Run ACDP Mini App Follow procedure below to […]
You are able to reset BMW FEM/BDC mileage with VVDI2/VVDI BIMTool, CGDI, and Yanhua Mini ACDP. ACDP Mini is easier comparing CGDI and VVDI. Here is […]
Problem: I have done a BMW E60 (CAS3+ ISTA4* version) all keys lost with Yanhua mini ACDP through OBD downgrade. Car did not start, the […]
One of Yanhua mini ACDP users was trying to read BMW MSV80 DME ISN with module 3 and interface board but failed. ACDP Mini says device […]
The BMW/mini Cooper EWS3 module is damaged and you would like to read date off the prossesor chip and then if you save it in […]
The 2022 new version Yanhua BMW FEM/BDC clip adapter is used to read 95128/95256 chip without soldering when pre-processing BMW FEM/BDC module. Function: No […]
There are two different (mirrored) MCU adapter cables being distributed with AK90+ models. Some have a black wire as pin 1 and some have the […]
Question: I failed to read BMW 2004 model EWS3 immo data with Autel IM608 Pro. Follow the instruction but gives a response timeout error. Solution: […]
Finally got the bar bmw/mini code remote to work with Autel IM608 (as well as IM508) so thought I would share. To find the option […]
Question: Anybody come across this issue? I’m trying to read DFlash or PFlash Cas4 on an F10 BMW 5M48H -with Autel IM608 outcome it reaches […]
Problem: Why autel im508 always get this error when i load dump from CAS3+ or any CAS dump? File version error code 4096. Failed to […]
Anyone use an old Autel maxisys BMW ENET cable adapter with MaxiIM IM608? Yes. You can use this cable, BMW F and G body program […]
2011 BMW 135i all keys lost was done with autel maxiim im608! Tried first to do all keys lost through IMMO status failed because of […]
I have BMW 116 2014 FEM. Autel IM608 says that version information and that I must restore eeprom data first! someone has reopen fem and […]
Can Autohex II Read BMW MSV70 on Bench? Autohex does not require open msv70 ecu to read isn. Check the wiring diagram connect wiring […]
BMW 7 series 2004 ME 9.2.2 ECU clone boot mode (BDM mode) ok with hextag programmer. It is done in boot mode because factory mode […]
Copyright © 2023 | WordPress Theme by MH Themes
This site is protected by wp-copyrightpro.com